stuartpittaway/diyBMS issues and pull requests

#37 - Suggestion: make the 5.08mm terminal holes a tad bigger

Issue - State: open - Opened by SergioRius about 3 years ago

#35 - current

Issue - State: open - Opened by kikiloaw almost 4 years ago

#34 - Atmega328 conversion

Issue - State: open - Opened by danpshyco over 4 years ago

#33 - Missing R5 from BOM

Issue - State: closed - Opened by jchengz over 4 years ago - 1 comment

#32 - Access to the interface when no internet connexion

Issue - State: closed - Opened by fjgaston about 5 years ago - 4 comments

#31 - When was R5 removed?

Issue - State: closed - Opened by Alpha-IT-Centre over 5 years ago - 3 comments

#30 - added digikey bom for easy parts ordering

Pull Request - State: closed - Opened by alexanderturner over 5 years ago - 1 comment

#29 - Am I blind, where is R11?

Issue - State: closed - Opened by codemonkey76 over 5 years ago - 1 comment

#28 - Smallerpcb

Pull Request - State: closed - Opened by stuartpittaway over 5 years ago

#27 - Confused

Issue - State: closed - Opened by mikegleasonjr over 5 years ago - 2 comments

#26 - Temp calibration

Issue - State: open - Opened by hepike over 5 years ago - 2 comments

#25 - PWM driven mosfet onstead of resistor (not an Issue)

Issue - State: open - Opened by uploader18 over 5 years ago - 8 comments

#24 - ATTiny acting weird

Issue - State: closed - Opened by fjgaston over 5 years ago - 2 comments

#23 - Update BMS_Cell_Module_BOM.html

Pull Request - State: closed - Opened by Zenkormalorvi over 5 years ago - 1 comment

#22 - ESP32 diyBMS

Issue - State: open - Opened by fjgaston over 5 years ago - 3 comments

#21 - Merge the nice features

Pull Request - State: closed - Opened by Valcob over 5 years ago - 12 comments

#20 - J1, C6 and C1 are very close on the PCB (v2.1)

Issue - State: open - Opened by fjgaston over 5 years ago - 11 comments

#19 - Don't hide password to WIFI.

Pull Request - State: closed - Opened by SanKen over 5 years ago - 2 comments

#18 - why 3.3V for the ATTiny ?

Issue - State: closed - Opened by fjgaston over 5 years ago - 4 comments

#17 - DIY BMS Stencil for 3D printing

Issue - State: closed - Opened by PapaStauth almost 6 years ago - 1 comment

#16 - Thermistor voltage divider in cold weather

Issue - State: closed - Opened by stuartpittaway almost 6 years ago - 1 comment

#15 - The term “Ground” on the cell module is not correct, it should be “Bat -”

Issue - State: open - Opened by stuartpittaway about 6 years ago

#14 - BOM updated

Issue - State: open - Opened by ArchGalileu about 6 years ago - 13 comments

#13 - Qi Charger for DC/DC Isolation and Dump Load?

Issue - State: closed - Opened by jamestutton about 6 years ago - 1 comment

#12 - Not compiling under Linux

Issue - State: closed - Opened by delboy711 about 6 years ago - 1 comment

#11 - Update R3 value in schematic to match pcb

Pull Request - State: closed - Opened by jessedc about 6 years ago

#10 - ESP code conver to Arduino Uno code

Issue - State: closed - Opened by EmreBostanci about 6 years ago - 26 comments

#9 - New PCB

Issue - State: closed - Opened by tvixen about 6 years ago - 5 comments

#8 - The direction of ALUM1250

Issue - State: closed - Opened by tvixen about 6 years ago - 9 comments

#7 - documentation

Issue - State: closed - Opened by tvixen over 6 years ago - 2 comments

#6 - Is resistor R2 too low?

Issue - State: closed - Opened by stuartpittaway over 6 years ago - 4 comments

#5 - Update Bill Of Materials in README for readability.

Pull Request - State: closed - Opened by jessedc over 6 years ago - 1 comment

#4 - Change capacitors to 1206 SMD sizes

Issue - State: closed - Opened by stuartpittaway almost 7 years ago - 3 comments

#3 - PCB works - almost!

Issue - State: closed - Opened by stuartpittaway almost 7 years ago - 4 comments

#2 - ADUM1251 footprint slightly too wide