Ecosyste.ms: Issues

An open API service for providing issue and pull request metadata for open source projects.

GitHub / sparkfun/qduino_mini issues and pull requests

#30 - no bounds checking

Issue - State: closed - Opened by chrwei about 9 years ago - 1 comment

#29 - attachinterrupt compile error

Issue - State: closed - Opened by JonathanFHill about 9 years ago - 2 comments

#28 - How to use "Status" LED?

Issue - State: open - Opened by Flat-earth-academy over 9 years ago - 8 comments

#26 - ground staking vias on usb anchor pads should be named gnd

Issue - State: closed - Opened by ghost over 9 years ago

#26 - ground staking vias on usb anchor pads should be named gnd

Issue - State: closed - Opened by ghost over 9 years ago

#25 - resistor arrays needs value corrected

Issue - State: closed - Opened by ghost over 9 years ago

#23 - D1 and Q1 could use values in sch on values layer

Issue - State: closed - Opened by ghost over 9 years ago - 1 comment

#22 - 8 LEDs

Issue - State: closed - Opened by BrentWilkins almost 10 years ago - 2 comments

#21 - unnecessary "PWR" label next to diode / switch on board

Issue - State: closed - Opened by MightyQ almost 10 years ago - 1 comment

#19 - SJ1 on backside needs to be internally connected

Issue - State: closed - Opened by MightyQ almost 10 years ago

#18 - master branch version: silk labels for jst terminals need to be moved upwards

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#17 - master branch version: switch not labeled in silk

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#16 - master branch version: SJ1 not labeled in bottom silk

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#15 - master branch version: bottom silk label "SCL" cut off by solder jumper

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#14 - master branch version: name of product needed in silkscreen

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#13 - master branch version: add staking via to outer two ground pads of usb connector

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#12 - master branch version: switch too close to dimension

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#11 - master branch version: unnecessary via under switch

Issue - State: closed - Opened by ghost almost 10 years ago - 2 comments

#10 - master branch version: unnecessary text object near jst

Issue - State: closed - Opened by ghost almost 10 years ago - 3 comments

#9 - vcc range needed in sch

Issue - State: closed - Opened by ghost almost 10 years ago - 3 comments

#8 - usb connector and related nets in sch could be flipped

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#7 - need vcc range in schematic

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#6 - large qduino logo on bottom will get cut by vias

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#5 - measurements in brd need to be on layer 47

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#4 - natural bridge needs to be removed on MAX17048 in brd

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#3 - reviser name needs to be included in sch and brd

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#2 - sparkfun and oshw logos needed in sch

Issue - State: closed - Opened by ghost almost 10 years ago - 1 comment

#1 - 3.3V regulator

Issue - State: closed - Opened by BrentWilkins almost 10 years ago - 7 comments