Ecosyste.ms: Issues

An open API service for providing issue and pull request metadata for open source projects.

GitHub / roboticsbrno/robutek issues and pull requests

#76 - Senzor numbering

Issue - State: open - Opened by TVavrinec about 1 month ago

#75 - Change analogue mux for line sensors

Issue - State: closed - Opened by TVavrinec 6 months ago

#74 - Make PWR and CHG LEDs different colors

Issue - State: closed - Opened by dzarda 7 months ago - 1 comment

#73 - Optimize for cost

Issue - State: open - Opened by dzarda 7 months ago

#72 - Eliminate power glitches when battery discharges <3V

Issue - State: closed - Opened by dzarda 7 months ago

#71 - Fix IO8 v IO18 label

Issue - State: closed - Opened by dzarda 7 months ago

#70 - Motor connectors

Issue - State: closed - Opened by dzarda 7 months ago

#69 - Octal SPIRAM not useable

Issue - State: closed - Opened by Tasssadar 7 months ago

#68 - Robutek docs

Pull Request - State: closed - Opened by C2Coder 7 months ago

#67 - chore: move robot render to main programming page

Pull Request - State: closed - Opened by Robot7769 7 months ago

#65 - Add simulator and corresponding lectures

Pull Request - State: closed - Opened by xondika 7 months ago

#64 - feat: added PCB render and fix pin IO8

Pull Request - State: closed - Opened by Robot7769 7 months ago

#63 - Gridui

Pull Request - State: closed - Opened by Tasssadar 7 months ago

#62 - Update Robutek library

Pull Request - State: closed - Opened by C2Coder 7 months ago

#61 - Lesson fixes 6-10

Pull Request - State: closed - Opened by JohnieWalkerCZ 7 months ago - 1 comment

#60 - Add Robutek-library to docs with index file

Pull Request - State: closed - Opened by C2Coder 7 months ago - 1 comment

#59 - Boot mód do lekce 1 při instalování Jacula

Pull Request - State: closed - Opened by jezura777 7 months ago

#59 - Boot mód do lekce 1 při instalování Jacula

Pull Request - State: closed - Opened by jezura777 7 months ago

#58 - restructured-docs

Pull Request - State: closed - Opened by JakubAndrysek 7 months ago

#57 - Přidán Jaculus install do lekce1.

Pull Request - State: closed - Opened by jezura777 7 months ago

#56 - finalize RobotAccessories

Pull Request - State: closed - Opened by C2Coder 7 months ago

#55 - Lekce6 rewrite

Pull Request - State: closed - Opened by jezura777 7 months ago

#54 - Lesson fixes

Pull Request - State: closed - Opened by JohnieWalkerCZ 7 months ago

#53 - Finish accessories and move it to a separate folder

Pull Request - State: closed - Opened by C2Coder 7 months ago

#52 - Setup PR Github Pages preview

Issue - State: open - Opened by JakubAndrysek 7 months ago
Labels: nice to have

#51 - Add partial stage3

Pull Request - State: closed - Opened by C2Coder 7 months ago

#50 - Zakladni osnova + par obrazku

Pull Request - State: closed - Opened by JakubAndrysek 8 months ago

#49 - Use softer buttons

Issue - State: closed - Opened by dzarda 8 months ago - 1 comment

#48 - Missing label

Issue - State: closed - Opened by Robot7769 8 months ago

#47 - Motor rotation turns device on

Issue - State: closed - Opened by dzarda 8 months ago

#46 - Move Micro-USB

Issue - State: closed - Opened by TVavrinec 8 months ago

#45 - Charger-LED bug

Issue - State: closed - Opened by dzarda 9 months ago

#44 - Reduce charging current below 1A

Issue - State: closed - Opened by TVavrinec 9 months ago

#42 - Add overcharge protection

Issue - State: closed - Opened by TVavrinec 9 months ago

#39 - Add ESD protection on micro-USB

Issue - State: closed - Opened by TVavrinec 9 months ago

#38 - Add pull-down resistor to MHL mux channel

Issue - State: closed - Opened by TVavrinec 9 months ago

#37 - Add PMOD connector

Issue - State: closed - Opened by TVavrinec 9 months ago

#36 - Add OFF button resistor

Issue - State: closed - Opened by dzarda 9 months ago

#35 - Maybe add RC filters on LineSensor signals?

Issue - State: closed - Opened by dzarda 9 months ago - 2 comments

#34 - Make motor slot dimensions symmetric

Issue - State: closed - Opened by dzarda 9 months ago

#33 - Reconcile line sensor names and orientation

Issue - State: closed - Opened by dzarda 9 months ago

#32 - Maybe define PMOD voltage by a solder jumper?

Issue - State: closed - Opened by dzarda 9 months ago

#31 - What's the deal here?

Issue - State: closed - Opened by dzarda 9 months ago - 9 comments

#30 - Increase BAT_SENSE divider reduction

Issue - State: closed - Opened by dzarda 9 months ago - 6 comments

#29 - Add capacitance on BAT_SENSE

Issue - State: closed - Opened by dzarda 9 months ago

#28 - Add INOKB pullup

Issue - State: closed - Opened by dzarda 9 months ago

#27 - Remove copper below charger

Issue - State: closed - Opened by dzarda 9 months ago

#26 - Unify signal via drill

Issue - State: closed - Opened by dzarda 9 months ago

#25 - What is the purpose of this divider?

Issue - State: closed - Opened by dzarda 9 months ago - 1 comment

#24 - Maybe simplify USB mux inversion

Issue - State: closed - Opened by dzarda 9 months ago

#23 - Add LineSens_.. resistors

Issue - State: closed - Opened by dzarda 9 months ago

#22 - Missing lable on Servos

Issue - State: closed - Opened by Robot7769 9 months ago

#21 - Add name and version label

Issue - State: closed - Opened by dzarda 9 months ago - 7 comments

#20 - Maybe increase pitch of motor connectors

Issue - State: closed - Opened by dzarda 9 months ago - 1 comment

#19 - Maybe have PWR led on PWR side of board

Issue - State: closed - Opened by dzarda 9 months ago

#18 - Maybe have ON amd OFF buttons on each side of USBC?

Issue - State: closed - Opened by dzarda 9 months ago - 1 comment

#17 - Add battery measurement

Issue - State: closed - Opened by dzarda 9 months ago

#16 - Add TVS to VBUS and 5V

Issue - State: closed - Opened by dzarda 9 months ago - 3 comments

#15 - Add diode VBUS->5V to allow functioning without battery

Issue - State: closed - Opened by dzarda 9 months ago

#14 - Connect line sensor mux Enable to Low

Issue - State: closed - Opened by dzarda 9 months ago

#13 - Add Encoder signal filters

Issue - State: closed - Opened by dzarda 9 months ago - 1 comment

#12 - Remove CP Tx/Rx LEDs

Issue - State: closed - Opened by TVavrinec 9 months ago

#11 - Remove INOKB LED

Issue - State: closed - Opened by TVavrinec 9 months ago

#10 - Invert INOKB->USB Mux logic

Issue - State: closed - Opened by TVavrinec 9 months ago - 1 comment

#9 - Move USB connectors further from the edge

Issue - State: closed - Opened by TVavrinec 9 months ago

#8 - Set THM to 0.8V

Issue - State: closed - Opened by TVavrinec 9 months ago

#7 - Bad label

Issue - State: closed - Opened by Robot7769 9 months ago

#6 - WS2812 footprint

Issue - State: closed - Opened by TVavrinec 9 months ago

#5 - Sharp corner

Issue - State: closed - Opened by TVavrinec 9 months ago

#4 - Motor connector

Issue - State: closed - Opened by TVavrinec 9 months ago - 1 comment

#3 - Micro USB

Issue - State: closed - Opened by TVavrinec 9 months ago - 1 comment

#2 - MOSFETs

Issue - State: closed - Opened by TVavrinec 9 months ago

#1 - CADLAB.io integration

Issue - State: open - Opened by JarekParal about 1 year ago