mcudude/microcore issues and pull requests

#163 - MicroCore doesn't work after update Arduino IDE for ver. 2.3.4

Issue - State: open - Opened by Denexp-1 3 months ago - 3 comments

#162 - Problems disabling safe mode.

Issue - State: open - Opened by XanCraft21 3 months ago - 4 comments

#161 - ATtiny10 support?

Issue - State: open - Opened by WestfW 5 months ago - 2 comments

#160 - -ffixed is no longer needed?

Issue - State: open - Opened by WestfW 5 months ago - 4 comments

#159 - What is the default Vref value set at for ATtiny13A?

Issue - State: closed - Opened by VidhuSarwal 5 months ago - 3 comments

#158 - Add slow mode for STK500

Pull Request - State: closed - Opened by radiantwave 6 months ago

#157 - PlatformIO: `-DCUSTOM_BAUDRATE` wrong documentation

Issue - State: closed - Opened by LoZioo 7 months ago - 1 comment

#156 - UART (Serial) on PIN5

Issue - State: closed - Opened by gavazquez 12 months ago - 1 comment

#155 - millis() prevents entering to sleep

Issue - State: open - Opened by lazarevd about 1 year ago - 2 comments

#154 - Attiny10 support

Issue - State: closed - Opened by Peterhj05 over 1 year ago - 2 comments

#153 - Help with sleep mode and reset

Issue - State: open - Opened by Bogdan2282 over 1 year ago - 1 comment

#152 - Problems with firmware

Issue - State: closed - Opened by Bogdan2282 over 1 year ago - 3 comments

#151 - Optimize shiftOut function a little

Issue - State: closed - Opened by marshfolx almost 2 years ago - 2 comments

#150 - Cant burn bootloader using 127khz internal oscilator

Issue - State: closed - Opened by darkmetalman almost 2 years ago - 3 comments

#149 - insomnia - if millis() is used it does not enter sleep mode

Issue - State: closed - Opened by kratochviljan almost 2 years ago - 4 comments

#148 - tone() not working

Issue - State: closed - Opened by kratochviljan almost 2 years ago - 2 comments

#147 - No programmer on Arduino 2

Issue - State: closed - Opened by kamilbystryk almost 2 years ago - 3 comments

#146 - Calling noTone() may leave pin high, drawing current

Issue - State: closed - Opened by pserwylo almost 2 years ago - 3 comments

#145 - operator bool for compatibility

Pull Request - State: closed - Opened by neu-rah about 2 years ago

#144 - Known issues with M1 MacBook Pro?

Issue - State: closed - Opened by jvlobo about 2 years ago - 14 comments

#143 - Error compiled for attiny13A

Issue - State: closed - Opened by EmSerg74 about 2 years ago - 7 comments

#142 - PWM Frequency change

Issue - State: closed - Opened by ltwin8 about 2 years ago - 10 comments

#141 - Automatically optimize away micros()

Issue - State: closed - Opened by MCUdude about 2 years ago - 5 comments

#140 - Update README.md

Pull Request - State: closed - Opened by dvk80 about 2 years ago - 1 comment

#139 - Update Watch_dog_timer.ino

Pull Request - State: closed - Opened by dvk80 over 2 years ago

#138 - Update Watch_dog_timer.ino

Pull Request - State: closed - Opened by dvk80 over 2 years ago - 2 comments

#137 - Prevent corruption of disassembler listing command for paths w/ spaces

Pull Request - State: closed - Opened by per1234 over 2 years ago - 1 comment

#136 - ```delayMicroseconds``` fails to compile with a non-constant argument

Issue - State: closed - Opened by arduino12 almost 3 years ago - 8 comments

#135 - Add OLED I2C display example

Pull Request - State: closed - Opened by kholia almost 3 years ago

#134 - PB0 acts really strange after attachInterrupt

Issue - State: open - Opened by imayoda about 3 years ago

#133 - increase ADCtouch sensivity with 10 instead of 8 bit resolution

Pull Request - State: closed - Opened by kai-morich about 3 years ago - 1 comment

#132 - Weird operator compilation error

Issue - State: closed - Opened by BlvckBytes over 3 years ago - 3 comments

#131 - Create a tiny flash write library

Issue - State: closed - Opened by MCUdude over 3 years ago

#130 - MIcroCore no longer appearing in the list of IDE supported boards

Issue - State: closed - Opened by MajicDesigns over 3 years ago - 1 comment

#129 - delayMicroseconds() does not support variables

Issue - State: closed - Opened by UnforeseenOcean over 3 years ago - 9 comments

#128 - A2 doesn't match pin when INPUT_PULLUP

Issue - State: closed - Opened by lunaoe over 3 years ago - 2 comments

#127 - Interrupts not enabled by default?

Issue - State: closed - Opened by cbpdk over 3 years ago - 1 comment

#126 - MIDI 31250 Baud Rate

Issue - State: closed - Opened by sharpie7 almost 4 years ago - 3 comments

#125 - Attiny13 - interrupt INT0 - problem

Issue - State: closed - Opened by Jordan-Szwejda almost 4 years ago - 17 comments

#124 - Invalid device signature for Attiny 13a

Issue - State: closed - Opened by varadhas almost 4 years ago - 13 comments

#123 - invalid conversion from 'int' to 'analog_pin_t' [-fpermissive]

Issue - State: closed - Opened by AchimPieters about 4 years ago - 1 comment

#122 - analogRead compile errors

Issue - State: closed - Opened by pokearoo about 4 years ago - 4 comments

#121 - Fixed typos in URLs

Pull Request - State: closed - Opened by Flo082002 about 4 years ago - 1 comment

#120 - How to update MicroCore last version in platformio ?

Issue - State: closed - Opened by Witawat about 4 years ago - 4 comments

#119 - badArg("Digital pin must be a constant")

Issue - State: closed - Opened by TheSpade69 about 4 years ago - 13 comments

#118 - Reading multiple analog pins fails to compile

Issue - State: closed - Opened by aspyra about 4 years ago - 11 comments

#117 - pullup declaration

Issue - State: closed - Opened by DROID8622 over 4 years ago - 1 comment

#116 - Installation with arduino-cli failed

Issue - State: closed - Opened by ArminJo over 4 years ago

#115 - Fix delay()

Pull Request - State: closed - Opened by ebuehrle over 4 years ago - 3 comments

#114 - pulseIn error attiny13a

Issue - State: open - Opened by yudimoss over 4 years ago

#113 - BOD low voltage lever around 3.3v disable attiny

Issue - State: closed - Opened by E3K4 over 4 years ago - 2 comments

#112 - Typo in core settings?

Issue - State: closed - Opened by AlexGyver over 4 years ago - 1 comment

#111 - Wiring issue in "MicroCore ATtiny13 minimal setup"?

Issue - State: closed - Opened by wmzart over 4 years ago - 2 comments

#110 - Cannot read from ADC1

Issue - State: closed - Opened by adamalfath over 4 years ago - 2 comments

#109 - Ultrasonic sensor issue

Issue - State: closed - Opened by SaiSandeepKantareddy over 4 years ago - 5 comments

#108 - is tools.avrdude.program used?

Issue - State: closed - Opened by nerdralph over 4 years ago - 1 comment

#107 - map function not working as expected

Issue - State: closed - Opened by momonator25 over 4 years ago - 4 comments

#106 - suggestion and question about platformIO.md

Issue - State: closed - Opened by Boteium over 4 years ago - 11 comments

#105 - (Serial.read blocking) error

Issue - State: closed - Opened by DominicanMS almost 5 years ago - 6 comments

#104 - Q: ATtiny13A, Vbg as input?

Issue - State: closed - Opened by rayholland almost 5 years ago - 2 comments

#103 - my Attiny13A require SCK pin (PB2) to pull to LOW to work properly.... I don't know what is going on...

Issue - State: closed - Opened by GluTbl almost 5 years ago - 3 comments

#102 - analogWrite bug?

Issue - State: closed - Opened by nerdralph almost 5 years ago - 3 comments

#101 - UART Serial library

Issue - State: closed - Opened by DominicanMS about 5 years ago - 33 comments

#100 - delayMicroseconds() is not working

Issue - State: closed - Opened by MikeX7 about 5 years ago - 2 comments

#99 - Software i2c library?

Issue - State: closed - Opened by MCUdude about 5 years ago - 7 comments

#98 - identify MicroCore version

Issue - State: closed - Opened by nerdralph about 5 years ago - 1 comment

#97 - Oscillator calibration sketch does not compile

Issue - State: closed - Opened by Win-doze about 5 years ago - 1 comment

#96 - put Serial on a diet

Issue - State: closed - Opened by nerdralph about 5 years ago - 21 comments

#95 - auto include millis

Pull Request - State: closed - Opened by nerdralph about 5 years ago - 2 comments

#94 - Transparent millis support?

Issue - State: closed - Opened by MCUdude about 5 years ago - 4 comments

#93 - Improve serial receive handling

Issue - State: closed - Opened by MCUdude about 5 years ago - 27 comments

#92 - Add Serial/UART support and oscillator calibration

Pull Request - State: closed - Opened by MCUdude about 5 years ago

#91 - improvement: only enable PWM in analogWrite()

Issue - State: closed - Opened by nerdralph about 5 years ago - 1 comment

#90 - always use LTO, remove option

Issue - State: closed - Opened by nerdralph about 5 years ago - 1 comment

#90 - always use LTO, remove option

Issue - State: closed - Opened by nerdralph about 5 years ago - 1 comment

#89 - Implement a sketch for tuning the internal oscillator

Issue - State: closed - Opened by MCUdude about 5 years ago - 26 comments

#88 - Bit-banged serial, baud rates and error

Issue - State: closed - Opened by MCUdude about 5 years ago - 42 comments

#87 - Tone 45% size reduction (350->194 bytes)

Pull Request - State: closed - Opened by nerdralph over 5 years ago - 2 comments

#86 - /bin/avr-g++ is in /ust/bin/avr-g++ and I can partly fix that problem

Issue - State: closed - Opened by clytle374 over 5 years ago - 1 comment

#85 - Pinout

Issue - State: closed - Opened by Ehsan-Shahnazi over 5 years ago - 14 comments

#84 - Fix Travis

Issue - State: closed - Opened by MCUdude over 5 years ago - 6 comments

#83 - add better option to disable millis()

Issue - State: closed - Opened by Master811129 over 5 years ago - 1 comment

#82 - make millis() interrupt safe

Issue - State: closed - Opened by nerdralph over 5 years ago - 1 comment

#81 - idea: include PCINT0 interrupt in Winterrupts.c

Issue - State: closed - Opened by jmerc77 over 5 years ago - 1 comment

#80 - aTTiny13A millis() MicroCore does not work

Issue - State: closed - Opened by DominicanMS over 5 years ago - 8 comments

#79 - Something wrong with variable memory allocation

Issue - State: closed - Opened by harrylisby over 5 years ago - 9 comments

#78 - If statement with two conditions

Issue - State: closed - Opened by opinto1 almost 6 years ago - 4 comments

#78 - If statement with two conditions

Issue - State: closed - Opened by opinto1 almost 6 years ago - 4 comments

#77 - Adding debugWIRE programmer

Pull Request - State: closed - Opened by taHC81 almost 6 years ago - 1 comment

#76 - Improve accuracy in micros() for nearly all clocks

Pull Request - State: closed - Opened by Jackjan4 almost 6 years ago - 6 comments

#75 - Add Boards Manager installation support for 1.0.4

Pull Request - State: closed - Opened by per1234 about 6 years ago - 1 comment

GitHub / mcudude/microcore issues and pull requests