google/OctoPrint-LEDStripControl issues and pull requests

#36 - Settings will not save and octo hangs

Issue - State: open - Opened by mchaos over 4 years ago

#35 - Plug-in enables two lights per one M150 command

Issue - State: open - Opened by professor305 over 4 years ago - 3 comments

#34 - Not an actual issue, more of a question.

Issue - State: closed - Opened by SleepyBlueCat almost 5 years ago - 1 comment

#33 - Not running consistently

Issue - State: open - Opened by GaWr26 about 5 years ago - 8 comments

#32 - Updating to work with python3 and OctoPrint 1.4.x

Pull Request - State: closed - Opened by precision about 5 years ago

#31 - Documentation link not working

Issue - State: closed - Opened by BomSquad about 5 years ago - 2 comments

#30 - After install, Octoprint can't start up

Issue - State: closed - Opened by tvixen over 5 years ago - 5 comments

#29 - After updating to newest octoprint version - only

Issue - State: closed - Opened by GunnarFrei over 5 years ago - 13 comments
Labels: invalid, wontfix

#28 - Wrong link for pigpiod.

Issue - State: closed - Opened by niai almost 6 years ago

#27 - Unable To Save Config Without Reboot Then Freeze

Issue - State: closed - Opened by thomasdlap almost 6 years ago - 7 comments

#26 - Orange Pi Support

Issue - State: closed - Opened by Bensmall about 6 years ago - 4 comments

#25 - Just a simple white LED strip

Issue - State: closed - Opened by Pyr3x about 6 years ago - 3 comments

#24 - Cabling + Compatibility Ender 3

Issue - State: closed - Opened by pika28 about 6 years ago - 9 comments

#23 - Help

Issue - State: closed - Opened by Scottyprogrammer over 6 years ago - 1 comment

#22 - M150 Codes Ignored By Terminal

Issue - State: closed - Opened by jmwright over 6 years ago - 2 comments

#21 - Cannot trigger with M150 command (Prusa I3 Mk2s)

Issue - State: closed - Opened by mikedmor almost 7 years ago - 9 comments

#20 - add a button on octopi page to light on/off the led

Issue - State: closed - Opened by blandiant almost 7 years ago - 1 comment
Labels: question

#19 - adressable leds

Issue - State: closed - Opened by cascha42 almost 7 years ago - 1 comment

#18 - Plugin does not save\function

Issue - State: closed - Opened by bi0hazard1980uk almost 7 years ago - 13 comments

#17 - KeyError: 'w'

Issue - State: closed - Opened by gulliverrr almost 7 years ago - 7 comments

#16 - Add support for RGBW LED strips as well as an option to initialize LEDs low on startup.

Pull Request - State: closed - Opened by precision almost 7 years ago

#15 - Problem LEDStripControl

Issue - State: closed - Opened by thomasnastorg almost 7 years ago
Labels: invalid

#14 - Not showin up in Plugins tab

Issue - State: closed - Opened by J0nny12 almost 7 years ago - 17 comments

#13 - Additional GPIO control

Issue - State: closed - Opened by jcsntoll about 7 years ago - 1 comment
Labels: enhancement

#12 - Setup?

Issue - State: closed - Opened by pokerpilot1994 about 7 years ago - 1 comment
Labels: question

#11 - Initialize led pins to low

Issue - State: closed - Opened by Davide-sd over 7 years ago - 2 comments
Labels: enhancement

#10 - Invalid gcode command

Issue - State: closed - Opened by charicner over 7 years ago - 16 comments
Labels: question

#9 - Will this work on common anode RGB LEDs? If not, what modifacations would need to be made to make it work?

Issue - State: closed - Opened by MrBreadWater over 7 years ago - 14 comments

#8 - getting the wrong colours

Issue - State: closed - Opened by nowkillkennys over 7 years ago - 2 comments

#7 - Noob question

Issue - State: closed - Opened by suprdave04 over 7 years ago - 12 comments

#6 - pigpiod support

Pull Request - State: closed - Opened by precision almost 8 years ago

#5 - Feature Request: UI button to run M150 command

Issue - State: closed - Opened by xstrex almost 8 years ago - 3 comments
Labels: enhancement

Ecosyste.ms: Issues

GitHub / google/OctoPrint-LEDStripControl issues and pull requests