damellis/cellphone2hw issues and pull requests

#33 - Incorrect pin numbering on GSM module analog inputs.

Issue - State: open - Opened by damellis over 10 years ago
Labels: bug, circuit

#33 - Incorrect pin numbering on GSM module analog inputs.

Issue - State: open - Opened by damellis over 10 years ago
Labels: bug, circuit

#32 - Update LED matrix case files for circuit with buzzer solder jumper.

Issue - State: open - Opened by damellis over 11 years ago
Labels: case

#32 - Update LED matrix case files for circuit with buzzer solder jumper.

Issue - State: open - Opened by damellis over 11 years ago
Labels: case

#31 - Try thinner LiPo batteries from Seeedstudio.

Issue - State: open - Opened by damellis over 11 years ago
Labels: components

#31 - Try thinner LiPo batteries from Seeedstudio.

Issue - State: open - Opened by damellis over 11 years ago
Labels: components

#30 - Enlarge hole in case to accommodate FTDI breakout board.

Issue - State: open - Opened by damellis over 11 years ago
Labels: case

#30 - Enlarge hole in case to accommodate FTDI breakout board.

Issue - State: open - Opened by damellis over 11 years ago
Labels: case

#29 - Switch to an 8-pin SIM socket.

Issue - State: open - Opened by damellis over 11 years ago
Labels: circuit, components

#29 - Switch to an 8-pin SIM socket.

Issue - State: open - Opened by damellis over 11 years ago
Labels: circuit, components

#28 - Connect FTDI header directly to microcontroller.

Issue - State: open - Opened by damellis over 11 years ago
Labels: circuit

#27 - Connect buzzer to the microcontroller instead of the GSM module.

Issue - State: closed - Opened by damellis over 11 years ago - 2 comments
Labels: circuit

#27 - Connect buzzer to the microcontroller instead of the GSM module.

Issue - State: closed - Opened by damellis over 11 years ago - 2 comments
Labels: circuit

#26 - Update case files for new display.

Issue - State: open - Opened by damellis over 11 years ago
Labels: case

#25 - Update circuit board for better display.

Issue - State: open - Opened by damellis over 11 years ago
Labels: circuit

#24 - Find a better display.

Issue - State: open - Opened by damellis over 11 years ago
Labels: components

#23 - Find Digi-Key replacements for the SparkFun parts.

Issue - State: open - Opened by damellis over 11 years ago
Labels: components

#22 - Create alternative (smaller / M0) screws holes in case.

Issue - State: open - Opened by damellis over 11 years ago
Labels: case

#21 - Adjust holes in case to align with larger holes in PCB.

Issue - State: open - Opened by damellis over 11 years ago
Labels: case

#20 - Enlarge holes for the buttons and speaker in the top plywood.

Issue - State: open - Opened by damellis over 11 years ago
Labels: case

#19 - Make holes in PCB bigger (for M2 screws).

Issue - State: closed - Opened by damellis over 11 years ago - 3 comments
Labels: circuit

#18 - Make footprints easier to hand solder

Issue - State: open - Opened by andershedberg over 11 years ago - 2 comments
Labels: circuit

#17 - Update screws holes in veneer hpgl and CDR files to correspond to the latest PCB files.

Issue - State: closed - Opened by damellis over 11 years ago - 1 comment
Labels: case

#16 - Make pads for reset button bigger.

Issue - State: closed - Opened by damellis almost 12 years ago - 1 comment
Labels: circuit

#15 - Use a battery connector that's easier to connect and disconnect.

Issue - State: open - Opened by damellis almost 12 years ago
Labels: components

#14 - Use an easier-to-solder speaker.

Issue - State: open - Opened by damellis almost 12 years ago
Labels: components

#13 - Use an easier-to-solder USB connector.

Issue - State: open - Opened by damellis almost 12 years ago
Labels: components

#12 - Indicate components outlines in the silkscreen.

Issue - State: closed - Opened by damellis almost 12 years ago - 1 comment
Labels: circuit

#11 - Indicate polarity of components in the silk screen.

Issue - State: closed - Opened by damellis almost 12 years ago - 1 comment
Labels: circuit

#10 - Use a proper flexure design for the buttons.

Issue - State: closed - Opened by damellis almost 12 years ago - 1 comment
Labels: case

#9 - Switch to microcontroller with integrated USB.

Issue - State: open - Opened by damellis almost 12 years ago
Labels: components

#8 - Connect the status pin of the LiPo battery charger IC to the microcontroller.

Issue - State: open - Opened by damellis almost 12 years ago
Labels: circuit

#7 - Connect the M10 status pin to the microcontroller.

Issue - State: open - Opened by damellis almost 12 years ago
Labels: circuit

#6 - Enlarge holes in bottom veneer to accommodate full diameter of the nut.

Issue - State: closed - Opened by damellis almost 12 years ago - 1 comment
Labels: case

#5 - Extend stop mask over traces connected to power and ground of the USB connector.

Issue - State: closed - Opened by damellis almost 12 years ago

#4 - Consider making the mounting holes bigger.

Issue - State: closed - Opened by damellis almost 12 years ago - 1 comment

#3 - Add VCC and GND to the header that breaks out the extra microcontroller pins.

Issue - State: open - Opened by damellis almost 12 years ago
Labels: circuit

#2 - Round the corners more.

Issue - State: closed - Opened by damellis almost 12 years ago - 1 comment

#1 - Move the hole near the battery connector farther from the edge of the PCB.

Issue - State: closed - Opened by damellis almost 12 years ago

GitHub / damellis/cellphone2hw issues and pull requests