cuspaceflight/okgo issues and pull requests

#70 - Options/settings

Issue - State: open - Opened by cillian64 about 9 years ago

#69 - More tolerant against packet loss

Issue - State: closed - Opened by cillian64 about 9 years ago

#68 - Control display ignition's channel status not control's

Issue - State: closed - Opened by cillian64 about 9 years ago

#67 - Make ignition loop asyncronous

Issue - State: closed - Opened by cillian64 about 9 years ago

#66 - Channel/master relay stick detection

Issue - State: open - Opened by cillian64 about 9 years ago

#65 - Watchdog timer

Issue - State: open - Opened by cillian64 about 9 years ago

#64 - Splashscreens on control

Issue - State: closed - Opened by cillian64 about 9 years ago

#63 - Complain of booted armed

Issue - State: closed - Opened by cillian64 about 9 years ago - 1 comment

#62 - HMAC auth/checksumming

Issue - State: closed - Opened by cillian64 about 9 years ago - 1 comment

#61 - Control's window

Issue - State: closed - Opened by cillian64 about 9 years ago - 1 comment

#60 - Redo control display

Issue - State: closed - Opened by cillian64 about 9 years ago

#59 - airplane mode

Issue - State: closed - Opened by cillian64 about 9 years ago - 1 comment

#58 - beeping.

Issue - State: closed - Opened by cillian64 about 9 years ago

#57 - Read SNR and RSSI and pick one and display them

Issue - State: closed - Opened by cillian64 about 9 years ago - 1 comment

#56 - Timers/timing based on sysclock instead of delays

Issue - State: closed - Opened by cillian64 about 9 years ago

#55 - Buzzer DAC

Issue - State: closed - Opened by cillian64 about 9 years ago - 1 comment

#54 - Initial values for all GPIOs in (ignition|control)_pins.c

Issue - State: closed - Opened by cillian64 about 9 years ago

#53 - Test continuity testing.

Issue - State: closed - Opened by cillian64 about 9 years ago - 2 comments

#52 - Find/order charge cable and good crimps

Issue - State: closed - Opened by cillian64 about 9 years ago - 2 comments

#51 - Test USB/serial cable

Issue - State: open - Opened by cillian64 about 9 years ago

#50 - Correct LCD delays to appropriate us values

Issue - State: closed - Opened by cillian64 about 9 years ago
Labels: okgo2-firmware, okgo2-general

#49 - Firing cables

Issue - State: closed - Opened by cillian64 about 9 years ago - 1 comment

#48 - Make radios chat

Issue - State: closed - Opened by cillian64 about 9 years ago - 1 comment
Labels: okgo2-firmware, okgo2-general

#47 - Control Display

Issue - State: closed - Opened by cillian64 about 9 years ago - 1 comment
Labels: enhancement, okgo2-control, okgo2-firmware

#46 - Yellow LED on left on both boards

Issue - State: closed - Opened by cillian64 about 9 years ago

#45 - Add charging (c091d) and firing connectors (neutrik) to schematics

Issue - State: open - Opened by cillian64 over 9 years ago

#44 - Find a power switch for control

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: enhancement

#43 - unmask back tracks on ignition

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: bug, okgo2-ignition

#42 - more ground stitching

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: okgo2-control

#42 - more ground stitching

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: okgo2-control

#41 - Properly cap filter linear reg on control

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: bug, okgo2-control

#40 - Investigate LED wire-mounting kit

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: enhancement, okgo2-general

#39 - put trimpot on ignition for buzzer

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: enhancement

#38 - 3v3 on control is messy

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: bug, okgo2-control

#37 - I made a note that RFM95Ws have incorrect pin directions in datasheets -- double check this

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: bug, duplicate, okgo2-general

#36 - Double-check DRC and ERC with correct design parameters

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: enhancement, okgo2-general

#35 - Lay out structure/flow of both firmwares

Issue - State: open - Opened by cillian64 over 9 years ago - 2 comments
Labels: okgo2-firmware

#34 - Design packet format

Issue - State: closed - Opened by cillian64 over 9 years ago - 2 comments
Labels: okgo2-firmware

#33 - Prep and order parts

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: okgo2-general

#32 - Order PCBs

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: okgo2-general

#31 - Tidying of ignition PCB

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: enhancement, okgo2-ignition

#30 - Tidying of control PCB

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: enhancement, okgo2-control

#29 - Move SWD on control somewhere sensible

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: bug, okgo2-control

#28 - Routing of decoupling capacitors

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: enhancement, okgo2-general

#27 - Think about antenna connections and waterproofing

Issue - State: closed - Opened by cillian64 over 9 years ago - 2 comments
Labels: enhancement, okgo2-general

#26 - Cable tie holes to tie down lipo

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: enhancement, okgo2-ignition

#25 - Find a keyswitch

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: enhancement, okgo2-control

#24 - Find a piezo and figure out how to waterproof, add to schematic and PCB!

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: enhancement, okgo2-ignition

#23 - flyback diodes on firing channels for actuating solenoids

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: enhancement, okgo2-ignition

#22 - Make mechanical holes have correct clearance markers and unmask

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: enhancement, okgo2-general

#21 - LCD voltages

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: okgo2-control

#20 - fix booster

Issue - State: closed - Opened by cillian64 over 9 years ago - 5 comments
Labels: bug, okgo2-control

#19 - USB interface

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: enhancement, okgo2-control

#18 - Relay flyback diodes?

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: okgo2-ignition

#17 - Change footprints to non-handsoldering

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: bug, okgo2-general

#16 - higher precision resistors for battery monitor

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: bug, okgo2-general

#15 - Check if drive resistor is on correct side of crystal / OSC_IN/OSC_OUT

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: bug, okgo2-general

#14 - Test points

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: okgo2-general

#13 - Add ESD diodes

Issue - State: closed - Opened by adamgreig over 9 years ago - 2 comments
Labels: enhancement, okgo2-control, okgo2-ignition

#12 - Relay failsafe circuit

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: enhancement, okgo2-ignition

#11 - Verify oscillator design

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: enhancement, okgo2-general

#10 - Connect up nRST from SWDIO connector to STM32?

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: bug, okgo2-control, okgo2-ignition

#9 - Confirm footprints

Issue - State: closed - Opened by cillian64 over 9 years ago - 3 comments
Labels: okgo2-general

#8 - Choose some connectors and stuff

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: okgo2-general

#7 - Part footprints

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: okgo2-general

#6 - Specify mechanical parts inc fixings

Issue - State: closed - Opened by cillian64 over 9 years ago - 3 comments
Labels: okgo2-general

#5 - Finalize pin assignment

Issue - State: closed - Opened by cillian64 over 9 years ago - 1 comment
Labels: okgo2-general

#4 - Specify parts (electrical)

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: okgo2-general

#3 - Reconsider/check/test continuity circuits

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: okgo2-ignition

#2 - Sort out mechanics

Issue - State: closed - Opened by cillian64 over 9 years ago - 2 comments
Labels: enhancement, okgo2-control, okgo2-ignition

#1 - De-specify SPI pins

Issue - State: closed - Opened by cillian64 over 9 years ago
Labels: bug, okgo2-control, okgo2-ignition

GitHub / cuspaceflight/okgo issues and pull requests