Ecosyste.ms: Issues
An open API service for providing issue and pull request metadata for open source projects.
GitHub / arksine/katapult issues and pull requests
#32 - Huvud no longer updates via flash_can.py
Issue -
State: closed - Opened by JamesH1978 over 2 years ago
- 15 comments
#31 - SKR V1.4 Turbo unable to reflash klipper
Issue -
State: open - Opened by Bazeone over 2 years ago
- 8 comments
#30 - Some SKR 1.4 Turbo observations
Issue -
State: closed - Opened by Sineos over 2 years ago
- 2 comments
#29 - LPC176x CanBoot and Klipper flashing
Issue -
State: closed - Opened by idontknowtom over 2 years ago
- 1 comment
#28 - STM32G0B1xx CanBoot with can possible?
Issue -
State: closed - Opened by Raabi91 over 2 years ago
- 22 comments
#27 - CanBoot specific USB id
Issue -
State: closed - Opened by KevinOConnor over 2 years ago
- 2 comments
#26 - Add support for lpc176x devices
Pull Request -
State: closed - Opened by Arksine over 2 years ago
- 2 comments
#25 - Support for additional stm32 chips
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 2 comments
#24 - Resync stm32f4 with upstream Klipper
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 1 comment
#23 - Default to 8KiB app start on f0/f1 ; Allow 16KiB on f4
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
#22 - Report pages written from "eof" command
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
#21 - Write each block individually ; no need for pages
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 2 comments
#20 - Add compile time check to initial_pins to reduce binary size
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 1 comment
#19 - Support 4KiB application start
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 2 comments
#18 - Add support for initial pins
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 1 comment
#17 - A few code fixes
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 1 comment
#16 - Call timer_setup() from sched_main()
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 11 comments
#15 - stm32: Add support for STM32F4 devices
Pull Request -
State: closed - Opened by Arksine over 2 years ago
- 2 comments
#14 - Add support for flashing over USB and UART
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 3 comments
#13 - Some suggestions for dev-protocol-20220505 branch
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 1 comment
#12 - canboot_main: rework protocol
Pull Request -
State: closed - Opened by Arksine over 2 years ago
- 3 comments
#11 - Verifying failed on GD32F103CB
Issue -
State: open - Opened by Telekatz over 2 years ago
- 4 comments
#10 - Autodetect stm32f103 flash page size
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 2 comments
#9 - Support entering bootloader on gpio pin state
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 3 comments
#8 - Resync main makefile with Klipper's main makefile
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
#7 - Do hardware reset before application start
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
- 1 comment
#6 - Comand protocol should have a CRC?
Issue -
State: closed - Opened by KevinOConnor over 2 years ago
- 6 comments
#5 - Makefile: Build with -Os instead of -O2
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
#4 - Use Klipper3d github http address
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
#3 - Use Klipper's nodeid to canbus_id scheme
Pull Request -
State: closed - Opened by KevinOConnor over 2 years ago
#2 - checksum error on STM32F103RBT6 (nucleo64)
Issue -
State: closed - Opened by cooked almost 3 years ago
- 1 comment
#1 - clarification on currently supported model
Issue -
State: open - Opened by cooked almost 3 years ago