CircuitSetup/Split-Single-Phase-Energy-Meter issues and pull requests

#78 - one channel CT channel reading differently

Issue - State: closed - Opened by chaseadam over 1 year ago - 26 comments

#77 - Installation help

Issue - State: open - Opened by k7faq over 1 year ago - 3 comments

#76 - Clarification on ESPHome configuration

Issue - State: closed - Opened by wilsongoode almost 2 years ago - 3 comments

#75 - Energy meter solar kit installation in EU

Issue - State: open - Opened by MassimilianoBiancucci almost 2 years ago - 2 comments

#74 - Calibration in EU with 230V 50Hz

Issue - State: open - Opened by MassimilianoBiancucci almost 2 years ago

#73 - Getting 65535 values for Current and voltage

Issue - State: open - Opened by abraralishah12 about 2 years ago - 9 comments

#72 - Current Multiplier and Wattage report Fixes

Pull Request - State: closed - Opened by DragonMinded over 2 years ago

#71 - Fix a few things with Home Assistant example

Pull Request - State: closed - Opened by DragonMinded over 2 years ago - 1 comment

#70 - volt is reading 0.001000

Issue - State: closed - Opened by kimza90 over 2 years ago - 1 comment

#69 - Why in the REGULAR ENERGY MEASUREMENT is done the product by 3200?

Issue - State: closed - Opened by amolina-chargevite over 2 years ago - 1 comment

#68 - Rebooting problem using emonESP with ESP32 with Arduino IDE

Issue - State: closed - Opened by albnar over 2 years ago - 7 comments

#67 - Error during compiling EmonESP scr.ino.

Issue - State: closed - Opened by albnar over 2 years ago - 1 comment

#66 - Alternative way to power the v1.4 board

Issue - State: closed - Opened by foureight84 over 2 years ago - 3 comments

#65 - fuse suggestion

Issue - State: open - Opened by chaseadam over 2 years ago - 1 comment
Labels: enhancement

#64 - Current and ADC voltage limits, and the PGA

Issue - State: open - Opened by raineth over 2 years ago - 2 comments
Labels: Documention

#63 - Voltage measurement under load?

Issue - State: closed - Opened by Cat-Ion over 2 years ago - 1 comment

#62 - CT Clamps not reading anything

Issue - State: open - Opened by smartroad over 2 years ago - 1 comment

#61 - How to avoid using Emon software

Issue - State: closed - Opened by Rivazinho over 2 years ago

#60 - Use another CT sensor.

Issue - State: open - Opened by Fresh878 over 2 years ago - 1 comment

#59 - Can I use a Jameco 112366 with board 1.4 rev3?

Issue - State: closed - Opened by rb28z2 almost 3 years ago - 1 comment

#58 - No Power with 3 different Jameco 9V Ac Adapters

Issue - State: closed - Opened by luisgarcia87 almost 3 years ago - 1 comment

#57 - cannot "unset" emoncms server in emonesp

Issue - State: open - Opened by chaseadam about 3 years ago
Labels: bug

#56 - Repeated MQTT reconnects due to emon server unavailable

Issue - State: closed - Opened by chaseadam about 3 years ago - 1 comment

#55 - FR: Add ClientId to MQTT

Issue - State: open - Opened by dimaj about 3 years ago
Labels: enhancement

#54 - Any advice for an european transformer brand?

Issue - State: closed - Opened by wouldgo about 3 years ago - 3 comments

#53 - Negative values?

Issue - State: closed - Opened by scfigg about 3 years ago - 1 comment

#52 - No AC adapter available

Issue - State: closed - Opened by eavyon over 3 years ago - 4 comments

#51 - support for high frequency AC transformer?

Issue - State: closed - Opened by asalexsu over 3 years ago - 5 comments

#50 - Setting up Split Single Phase meter on emoncms.org

Issue - State: closed - Opened by farzadb over 3 years ago - 3 comments

#49 - Calibration emonESP from Russia

Issue - State: closed - Opened by skribbl84 over 3 years ago - 1 comment

#48 - Board Compatability

Issue - State: closed - Opened by johnsethwatkins over 3 years ago - 1 comment

#47 - fried split circuit v1.4 rev 2

Issue - State: closed - Opened by chaseadam over 3 years ago - 2 comments

#46 - What is the latest version 2.6 or 2.6.1

Issue - State: closed - Opened by JPElectron over 3 years ago - 3 comments

#45 - Reading 65k from voltage register

Issue - State: closed - Opened by TSMotter over 3 years ago - 5 comments

#44 - Power is showing negative now?

Issue - State: closed - Opened by scfigg almost 4 years ago - 7 comments

#43 - What Calibration setting value to use for 200A CT?

Issue - State: closed - Opened by JPElectron almost 4 years ago - 5 comments

#42 - Can't connect to Emoncms after updating from 2.5.7 to 2.6

Issue - State: closed - Opened by zirdum almost 4 years ago - 7 comments

#41 - Switched routers... device won't connect to wifi

Issue - State: closed - Opened by zirdum almost 4 years ago - 1 comment

#40 - Verifying Power Factor values

Issue - State: closed - Opened by chaseadam almost 4 years ago - 4 comments

#39 - fix config loading to accept '0' to disable PGA

Pull Request - State: closed - Opened by chaseadam almost 4 years ago

#38 - EmonESP fork

Issue - State: closed - Opened by chaseadam about 4 years ago - 3 comments

#37 - Can't flash latest esphome example

Issue - State: closed - Opened by jarrettv about 4 years ago - 3 comments

#36 - Can we measure current with one CT only?

Issue - State: closed - Opened by aaamitsingh about 4 years ago - 8 comments

#35 - Won't Connect to MQTT Until Restart

Issue - State: closed - Opened by rothnic about 4 years ago - 2 comments
Labels: bug

#34 - No readings from CT2

Issue - State: closed - Opened by neilrees over 4 years ago - 3 comments

#33 - I am getting smoke from board on IC2

Issue - State: closed - Opened by RichBoehle over 4 years ago - 1 comment

#32 - When in STA mode connected to AP and AP goes away, will not auto reconnect

Issue - State: closed - Opened by kirkdwilson over 4 years ago - 1 comment

#31 - emonESP split phase - can I use for single phase?

Issue - State: closed - Opened by m-d-johnson over 4 years ago - 6 comments

#30 - Voltage * Current != Active Power, is that correct?

Issue - State: closed - Opened by manutenfruits over 4 years ago - 4 comments

#29 - Voltage calibration value

Issue - State: closed - Opened by gigawatts over 4 years ago - 1 comment

#28 - No Hardware

Issue - State: closed - Opened by palmtreefrb over 4 years ago - 5 comments

#27 - Periodic disconnects - add scheduled reboot?

Issue - State: open - Opened by amil109 over 4 years ago - 44 comments
Labels: bug

#26 - Fix for MQTT brokers used by hass.io not connecting when anonymous

Pull Request - State: closed - Opened by djryanj over 4 years ago - 1 comment

#25 - Update ATM90E32_Basic_SPI.ino

Pull Request - State: closed - Opened by mrarmyant over 4 years ago

#24 - Update README.md

Pull Request - State: closed - Opened by wthomson over 4 years ago

#23 - FR: Adjust Publish Rate for MQTT

Issue - State: open - Opened by politekcmo almost 5 years ago - 3 comments
Labels: enhancement

#22 - Feature Request: RSSI value MQTT feed

Issue - State: closed - Opened by gigawatts almost 5 years ago - 11 comments

#21 - Password Reset

Issue - State: closed - Opened by catalinalb almost 5 years ago - 3 comments

#20 - 240V and 60Hz?

Issue - State: open - Opened by CircuitSetup almost 5 years ago - 4 comments
Labels: bug

#19 - Power factor value alternating +ve/-ve in ATM90E32.cpp

Issue - State: closed - Opened by gbeardall almost 5 years ago - 6 comments

#18 - How to calculate CurrentGainCT#

Issue - State: closed - Opened by lanhtudongxanh almost 5 years ago - 2 comments

#17 - External wifi antenna?

Issue - State: closed - Opened by BitKnitting almost 5 years ago - 3 comments

#16 - Code for 6 channel board?

Issue - State: closed - Opened by p-doyle almost 5 years ago - 2 comments

#15 - Code for micropython/ESP32

Issue - State: open - Opened by BitKnitting almost 5 years ago - 1 comment

#14 - Strange data shown by energy meter

Issue - State: closed - Opened by gurari almost 5 years ago - 2 comments

#13 - Does Current Transformer Hookup Photo match the instructions?

Issue - State: closed - Opened by lyzby almost 5 years ago - 2 comments

#12 - Can't complile EmonESP code using platformio

Issue - State: closed - Opened by veggie2u almost 5 years ago - 11 comments
Labels: bug

#11 - Can't Post Data from ESP to EmonCMS via MQTT

Issue - State: closed - Opened by veggie2u almost 5 years ago - 3 comments

#10 - ESP not sending data to EmonCMS via MQTT

Issue - State: closed - Opened by veggie2u almost 5 years ago - 1 comment

#9 - The fields sent from ESP don't match CircuitSetup defaults on SD card image

Issue - State: closed - Opened by veggie2u about 5 years ago - 3 comments

#8 - Unable to join WiFi Network when Unicode SSID is visible

Issue - State: open - Opened by mfreymond about 5 years ago - 1 comment
Labels: bug

#7 - Calibration setting for 240V regions

Issue - State: closed - Opened by amil109 about 5 years ago - 12 comments

#6 - Using web interface and/or leaving it open causes ESP32 memory leak/crash

Issue - State: closed - Opened by CircuitSetup about 5 years ago - 5 comments

#5 - Errors compiling firmware (+suggested fix)

Issue - State: closed - Opened by kobuki about 5 years ago - 5 comments

#4 - Issue with device crashing after x hours SSPEM

Issue - State: closed - Opened by jreiners about 5 years ago - 21 comments

#3 - Using with single phase UK (240v) mains power

Issue - State: closed - Opened by motechsolutions about 5 years ago - 15 comments

#2 - Organized the energy meter specific code

Pull Request - State: closed - Opened by dgmltn over 5 years ago

#1 - Caps on schematic?

Issue - State: closed - Opened by BitKnitting over 5 years ago - 2 comments

GitHub / CircuitSetup/Split-Single-Phase-Energy-Meter issues and pull requests